53-Inch 430 Stainless Steel Antenna Wall Mount, Adjustable J-Pole Mast, 1.38-Inch OD, Silver
53-inch modular 430 stainless steel J-pole with a 1.38-inch OD mast, adjustable pivot base and 3-screw lock. For TV antennas, wireless bridges and weather stations. Starlink adapter required.
EOQO 53-Inch Adjustable Antenna Wall Mount – Long-Reach 430 Stainless Steel J-Pole
Mount outdoor antennas and networking devices where shorter brackets cannot provide enough height or clearance. The EOQO 53-inch antenna wall mount combines a modular silver 430 stainless steel mast, an adjustable pivot base and a three-screw locking connection. Its 1.38-inch (35 mm) outside diameter makes it suitable for many compatible antenna clamps and pole-mount accessories.
53-INCH MODULAR MAST FOR EXTRA CLEARANCE
The assembled long-mast configuration reaches approximately 53 inches (135 cm), helping lift compatible equipment above roof edges, gutters and nearby obstructions. Connect the supplied mast sections to build the configuration needed for your installation. The 53-inch figure describes approximate mast length, not guaranteed horizontal clearance from the wall.
430 STAINLESS STEEL – NATURALLY MAGNETIC
Manufactured from ferritic grade 430 stainless steel with a silver finish and a nominal 1 mm tube wall. This stainless steel grade is naturally magnetic; attraction to a magnet is normal and does not indicate that the mast is made from ordinary iron. It offers corrosion resistance for suitable outdoor applications, but is not rust-proof in every environment. Inspect the mast and fasteners periodically, especially in coastal or corrosive conditions.
ADJUSTABLE PIVOT BASE WITH THREE-SCREW LOCKING
Set the mast angle at the base to improve vertical alignment on suitable exterior walls and eave or roof-edge structures, then secure the three locking screws. This adjustment helps position antennas, weather sensors and outdoor WiFi equipment while reducing interference from nearby building features. The pivot is a positioning feature, not a substitute for adequate structural anchoring.
1.38-INCH OUTSIDE DIAMETER
The 1.38-inch (35 mm) OD mast fits many clamps designed for this pipe size. Verify the mounting hardware, clamp range, device weight and installation geometry before ordering. Do not assume every antenna, satellite terminal or pipe adapter will attach directly.
VERSATILE OUTDOOR APPLICATIONS
-
Over-the-air TV antennas
-
Weather stations and environmental sensors
-
Point-to-point wireless bridges and outdoor CPE devices
-
Outdoor WiFi access points, routers and extenders designed for pole mounting
-
Other compatible mast-mounted communication equipment
STARLINK INSTALLATIONS REQUIRE AN ADAPTER
The mast is not a direct-fit mount for a Starlink dish. A separate, model-specific Starlink pipe adapter is required and is not included. Check the adapter's accepted mast diameter and compatibility with your exact Starlink dish before purchase. The Starlink terminal, antennas, weather instruments and electronic devices are not included.
INSTALLATION AND WIND-SAFETY NOTES
Install the base only on a structurally suitable surface, using anchors and fasteners appropriate for the substrate and local building requirements. Fully seat the extension sections and carefully tighten the connecting screws. Avoid overtightening: excessive force may deform the 1 mm-wall tubing. Because a longer mast increases leverage, assess the attached equipment's projected wind area and consider additional bracing where needed. Installation or use in winds exceeding Beaufort Force 6, or during severe weather, is not recommended. No universal weight or wind-load rating is claimed.
PRODUCT SPECIFICATIONS
Brand: EOQO
Type: Adjustable modular J-pole antenna wall mount
Material: Ferritic 430 stainless steel
Finish: Silver
Approximate extended mast length: 53 in (135 cm)
Mast outside diameter: 1.38 in (35 mm)
Nominal tube wall thickness: 1 mm
Base: Adjustable pivot
Locking system: Three-screw connection
Starlink compatibility: Requires a suitable separate model-specific adapter
BEFORE YOU BUY
Measure the required clearance, verify your equipment's clamp size and confirm the mounting surface and fasteners are appropriate for the installation. Check the selected kit's package contents before installation.
Secure Checkout & Data Protection
Fast & Reliable Worldwide Shipping
Easy Returns & Hassle-Free Support
Comments (0)
Your review appreciation cannot be sent
Report comment
Report sent
Your report cannot be sent