• CPE450 wireless bridge is a 5.8G Long Range WiFi Extender Outdoor wireless bridge CPE with LED display. Point-to-point pairing can be done by dialing without having to access the GUI, avoid the complex setup program, save much human work and cost, make the long-range wireless coverage, data transmit and wireless monitoring simple and professional.
• 3KM Transmission Distance: 1.86 miles (visible unobstructed environment), actual application distance should be less than 3KM. Built-in 14DBi directional antenna can significantly improve the transmission and reception performance of wireless signals. Trees will not block the transmission speed of the point to point internet wireless bridge, suitable for warehouses or garages next to your house.
• Ethernet WiFi bridge pairing can be done by dialing, avoid the complex setup program, save much human work and cost, make the long-range wireless coverage, data transmit and wireless monitoring simple and professional. 2-pack CPE has been pre-configured/complete the pairing, you don't need to pair again, if you need to change the parameters, you can dial to pair. Dialing to set the transmitter and receiver, and also support the PC to modify the IP setting.
• Access CPE via PC: Point to point bridge is manageable through the WEB browser interface. Before accessing, please modify the IP address of the computer to the same network segment as the CPE (192.168.255.XXX), which is very important; then enter the IP address of the CPE in the browser, and enter the account password "admin/admin" to access and set. If you can’t set it up, please let us know.
• Low Interference& Outdoor Waterproof: 5.8G frequency makes long range wireless bridge has better anti-interference performance, good compatibility, and strong anti-adjacent channel interference, better than 2.4G traditional CPE. CPE450 network bridge is very suitable for outdoor use, with rain, dust, and antifreeze characteristic.

Wireless Bridge CPE450 Kits, Extend your Network form One Building to Another without Wire Connection

Great for share internet network to a long distance, works as outdoor access point, management video surveillance for different building

The CPE450 kits is one pair of outdoor high power and high performance 300Mbps wireless bridges, which works at 5GHz frequency. Supports Point-to-Point and Point-to-Multipoint wireless connection. It is more stable and higher speed and anti-interference performance than 2.4GHz wireless bridge. Moreover, it is easy to manage through the WEB interface.

CPE450 Kits Function:

1. the device can works as Auto pairing mode: simply to use, connect both bridges to the PoE power adapter to start working, it will auto pair in few minutes. Customize mode: need connect the bridges to the computer through ethernet cable, and configure the master & slave parameters, this mode suit for experienced technician.
2. the device can use for share internet networks to a long distance, output WiFi hot point, also can use for transmit the long ranges IP cameras' video stream to the control center without complicated wiring connection.
3. Auto pairing mode works for point-to-point access connection, customize mode can configure the point to multiple point connection.

CPE450 Kits Application:

1. Share internet networks to a longer distance, the master bridge gets internet and transfer to slave which can connect to router or computer
2. Outdoor access point, the master bridge connects to internet source and output WiFi hot point transmit up to 1.8miles & 60 degrees angle, you can get access the WiFi hot point in this area.
3. Connect the IP cameras from another building without wire connection, you can management the different place IP cameras in one DVR system.
4. Point to multiple point access, you can connect multiple slave bridges, to management more than one building's IP cameras in one DVR system.

Point-to-Point Connection for Extend Internet Network

Connection Guide

The master bridge and slave bridge must be installed by face to face, the antenna is not omnidirectional, it has a 60 degrees transmission angle, the straight installation without blocking objects would be the best performance.

Wireless Bridge Master & Slave Set:

1.Master Bridge Setting

Move the mode switch to "A" position, the device works as master bridge

2.Slave Bridge Setting

Move the mode switch to "B" position, the device works as slave bridge

Wireless Bridge Connection

1.Bridge A Connection - Master Bridge

Step 1: the LAN port of the PoE Adapter connect to the router through an ethernet cable.

Step 2: the PoE port of the PoE adapter connect to LAN port of the master wireless bridge by another ethernet cable.

2.Bridge B Connection - Slave Bridge

Step 1: the PoE port of the PoE adapter connect to the LAN port of slave bridge through an ethernet cable

Step 2: the LAN port of the PoE adapter connect to the LAN port of the computer or router by another ethernet cable

Point-to-Point Connection for Video Surveillance

Connection Guide

The master bridge and slave bridge must be installed by face to face, the antenna is not omnidirectional, it has a 60 degrees transmission angle, the straight installation without blocking objects would be the best performance.

Wireless Bridge Master & Slave Set:

1.Master Bridge Setting

Move the mode switch to "A" position, the device works as master bridge

2.Slave Bridge Setting

Move the mode switch to "B" position, the device works as slave bridge

Wireless Bridge Connection

1.Bridge A Connection - Master Bridge

Step 1: the LAN port of the PoE Adapter connect to the DVR through an ethernet cable.

Step 2: the PoE port of the PoE adapter connect to LAN port of the master wireless bridge by another ethernet cable.

2.Bridge B Connection - Slave Bridge

Step 1: the PoE port of the PoE adapter connect to the LAN port of slave bridge through an ethernet cable

Step 2: the LAN port of the PoE adapter connect to the LAN port of the switch by another ethernet cable

Point-to-Multiple Point Connection for Video Surveillance

Connection Guide

The master bridge and slave bridge must be installed by face to face, the antenna is not omnidirectional, it has a 60 degrees transmission angle, the straight installation without blocking objects would be the best performance.

Wireless Bridge Master & Slave Set:

1.Master Bridge Setting

Move the mode switch to "A" position, the device works as master bridge

2.Slave Bridge Setting

Move the mode switch to "B" position, the device works as slave bridge

Wireless Bridge Connection

1.Bridge A Connection - Master Bridge

Step 1: the LAN port of the PoE Adapter connect to the DVR through an ethernet cable.

Step 2: the PoE port of the PoE adapter connect to LAN port of the master bridge by another ethernet cable.

2.Bridge B Connection - Slave Bridge

Step 1: the PoE port of the PoE adapter connect to the LAN port of slave bridge through an ethernet cable

Step 2: the LAN port of the PoE adapter connect to the LAN port of the IP cameras by another ethernet cable

CPE450 Wireless Bridge Interface

Overview

The wireless bridges work by two modes, auto pairing mode with pre-programmed suit for newbie and customize mode suit for experienced user.

Auto pairing mode:

Connect the bridges to the PoE power adapter, the Power LED lamp turns green, system is power on, when both bridges are power on, they will auto pair in a few minutes, during the pairing the LAN status LED lamps all turn green. The digital LED indicator displays the numeric in red color.

You can find a good frequency without interference by pressing the "RST" button to change the channel, short press the button, the LED indicator will display the numeric "0","1","2","3"..."F" one by one, and change in cycle, each numeric means a different frequency, you can find the details in the user manual.

At the auto pairing mode, the bridge also output WiFi hot point, and the access password is pre-programmed in auto paring mode. When the channel changes, the access password changes as well. For example: the WiFi hot point name is CPE5G_5G161, and the default password is zllinkcpe123456161, if the name is CPE5G_5G153, the password will be zllinkcpe123456153. The last three numbers of the password must match the last three numbers of the name.

Customize mode:

At this mode the bridged must be connected to the computer and set different IP addresses and working modes, short press the "RST" button will not functional at this mode, but you can press and hold this button for over 10 seconds to reset to factory setting.

Application

Parameters