Functions:
G618W RF detector is made by new generation wireless technology, mainly designed to detect GSM bug, wireless audio bug, GPS tracker, mobile phone secret communication, spy WiFi camera, cheating device etc.
The function can meet military/police surveillance, it can detect electrical source, so will prevent you and your family from the damage of electromagnetic radiation. It adopts digital receiving mode, which is different from other detectors.
First is widen the detection frequency domain, avoid the disturbance from clutter signal of life.
Second is improved the sensitivity, the advantage is that no matter how strong the transmitting signal is, it can easily locate it by adjusting the switch.
So it is the most advanced portable wireless signal detection equipment. The normal wireless detector can not detect CDMA/4G/5G signal, if you dial it via CDMA 2100Mhz/4G 2300Mhz/5G 3600Mhz,the traditional detector never alarm.
Because CDMA/4G/5G mobile phone agreement was invented by the U.S.Military, it is a radio frequency hooping technology, was called code division multiple access, and the transmission power is small, it is hard to detect.
G618W can accurately identify the CDMA/4G/5G mobile communication protocol of monitoring equipment.
Overview:
Indicator LED Light: there are totally 10 LED lights, the first to the tenth LED bar is shown as 10 levels of the sensitivity, when a light is turned on, it means the level of the sensitivity is active, when all LED lights are flashing, it means the sensitivity is reaches the maximum value.
Switch: The switch is movable, move to "S" position works as signal detect mode, move to "D" position works as magnetic signal detect mode.
Button: Press and hold it for 3 seconds to change the alarm mode to vibrating, press and hold 3 seconds again, it will change back to sound alarm, works in cycle.
Power Switch & Sensitivity knob:
Turn it to right to power on and increase the sensitivity, turn it to left to decrease the sensitivity and power off.
Antenna:
The G618 has two antenna connectors, they are marked as “GSM”,“RF”, must check and match it one by one before installation.
Magnet Detect Probe: Connect the magnetic probe to the connector socket and screw it.
USB Port: Charging socket
Instructions:
Power ON: Turn the power switch by clockwise to power on, the indicator light will turn on, when rotate it to the end, the all LED lights will flash, and the device prompts "beep”, “beep" voice alarm rapidly.
Power OFF: Turn the power switch to the end by counterclockwise, the LED light will turn off, and the device power off.
A: RF Wireless Signal Detection:
Power on the device, move the mode switch to "S" position, the system works wireless detect mode, hold the device and the antenna forward to the target area, when receive signals, the device will prompts sound alarm and indicator LED lights will flash.
How to adjust the sensitivity and find the object?
The device has totally 10 levels of the sensitivity, adjust the power switch to appropriate sensitivity level, if the environmental signal is strong, you need decrease the sensitivity, normally we suggest you set it to level 7 or 8.
when close to the target, the 10 indicator LED lights bar will bright and flash, and the device prompts "beep”, “beep" sound alarm, it will alarm as rapidly when it is close to the target. You can try different sensitivity levels to find out the suspicious target.
Note:
This product is highly sensitive, it can receive wireless signals from cell phone base stations, television broadcasting stations on the road, if you need to use this device to find out the vehicle GPS tracker, please drive your car/truck to a weak signal area, and turn your cell phone to airplane mode, then start detection job, it will have better performance.
If the device always alarm and there is no any suspicious object, please check:
1. Your own electronic device has connection to the network station(you need to turn it off)
2. The target device may be in another room or at the other side of the wall, or one person who is near to the room makes phone calls.
3. Your place is too close to the network station.
B. Magnetic Probe Detection:
Power on the device, move the mode switch to "D" position, the system is works as magnetic detect mode, hold the device and forward the probe to target area, when it detected magnetic device, the probe light will turn on and the device will produce "beep","beep" sound alarm, it will alarm as rapidly when it is close to the suspicious target.
Alarm Sound and Vibration:
The device default alarm is sound, produce "beep" sound alarm, you can press and hold the button for 3 seconds to change to vibration alarm mode, press it 3 seconds again back to sound alarm.
Charging:
Connect it to power adapter via USB cable, the charging LED will turn blue, when it charged full will turn red.
Parameters:
Frequency Range: 100MHz - 2700MHz
Detect Dynamic Range: >73db
Detection Sensitivity: <0.03mw
Detect Range: 1.2GHz wireless camera: 10m², 2.4GHz wireless camera: 15m²(transmitter: 10mw)
Magnetic: 10 - 20mm
Pinhole Camera Lens: 10 - 20 meters
Mobile: 2G,3G,4G,5G: 10m²
Battery: 3.7V 1000Mah
Working Current: 60Mah
Working Time: 8 - 12 hours
Weight: 120g
Warning:
Application: Please strictly abide relevant regulations and laws. This product should not be used for any illegal purposes. The user is fully responsible for its use.
Battery: If this product has not been used in a long period of time, you will need to fully charge it before using.
Operating temperature: 0 - 40 degree.
Operating humidity: 20% -80%, this product is not waterproof so do not get it wet or use it in a humid environment.
Other matters: Do not use this product in strong magnetic or strong electric powered environments.
Please visit http://www.eoqo.com for operation videos and more use guide.